Don't Wait Until It's Too Late!
Protect Your Basement With A Backup
Sump Pump from Rain One
Don't Wait for Disaster
Avoid the potential of a flooded basement with a back-up sump pump.
A backup sump pump can prevent catastrophe. It is also recommended to replace your main sump pump every 7 to 10 years to avoid potential failure. The small initial cost will always weigh less than the burden and inconvenience of the aftermath of such a storm.
While we offer many different options with Sump Pump Systems, we prefer a system that includes both primary and secondary pumps, battery, and charger.
Pricing
The following pricing includes labor and material for a typical install. If the installation is not typical, the technician dispatched for your installation will inform you of any additional charge prior to starting. If you would like an exact estimate, please contact us to make arrangements.
Combination Primary/Back-Up
1/3 HP Sump Pump and Back-Up System from
$1,299 Installed!* BEST VALUE!
1/3 HP 68 GPM: 60 GPM @ 5'
CONSTRUCTION
Assembled in the US with foreign and domestic parts
Tested to 1 million cycles* (Primary only)
Cast Iron Pump Housing/Base withTop Suction Intake to Filter Debris and Minimize Clogging
Corrosion-Resistant Thermoplastic Engineered Flow Divertor, for Switch Protection
Stainless Steel Upper and Lower Float Guard and Float Guide
Corrosion-Resistant Thermoplastic Impeller for Maximum Water Flow, and Long Life in Tough Sump Applications.
1-1/2 in. NPT Discharge for Easy Installation and Compliance with Building Codes
Engineered to Pass Up to 1/2 in. Solids
For Use In 11 in. Diameter or Larger Sump Basins
10 ft. SJTW Power Cord
SWITCH
Two-Pole Snap-Action Integrated Mechanical Float Switch
ON @ 9 in. / OFF @ 4 in.
SEALS
Carbon / Ceramic Shaft Seal for Maximum Life
MOTOR
120 Volt, PSC Oil-Filled Motor
Upper and Lower Ball Bearings for Smooth, Quiet Operation and Long Life
Continuous Duty Capability
Low Amp Draw for Maximum Switch Life
* Typical Installation
12-Volt Battery Back-Up Sump Pump System $989 Installed!*
Assembled in the US with foreign and domestic parts
Fully Submersible Back Up Pump, for An Easy Addition To Any Sump System
Corrosion-Resistant Thermoplastic Construction for Long Life in Tough Sump Applications
Corrosion-Resistant Thermoplastic Impeller for Maximum Water Flow
Protective Battery Case Included with LED Display and Audible Alarm to Let Homeowner Know There’s a Problem
1-1/2 in. NPT Discharge for Easy Installation and Compliance with Building Codes
For Use In 14 in. Diameter or Larger Sump Basins
SwitchReliable Reed Float Switch with Float Cage for Added Protection
ON / OFF Levels are User Adjustable
MOTORPowerful 12 VDC Motor, with Pumping Capacity that Nearly Matches an AC Powered Pump
* Typical Installation
Primary Pump Only
1/3 HP with Switch Genius Technology™ Cast-Iron Pump $445 Installed!*
Assembled in the US with foreign and domestic parts
Tested to 1 million cycles*
Cast Iron Pump Housing/Base with Top Suction Intake to Filter Debris and Minimize Clogging
Corrosion-Resistant Thermoplastic Engineered Flow Divertor, for Switch Protection
Stainless Steel Upper and Lower Float Guard and Float Guide
Corrosion-Resistant Thermoplastic Impeller for Maximum Water Flow, and Long Life in Tough Sump Applications.
1-1/2 in. NPT Discharge for Easy Installation and Compliance with Building Codes
Engineered to Pass Up to 1/2 in. Solids
For Use In 11 in. Diameter or Larger Sump Basins
10 ft. SJTW Power Cord
Switch
Two-Pole Snap-Action Integrated Mechanical Float Switch
ON @ 9 in. / OFF @ 4 in.
SEALS
Carbon / Ceramic Shaft Seal for Maximum Life
MOTOR
120 Volt, PSC Oil-Filled Motor
Upper and Lower Ball Bearings for Smooth, Quiet Operation and Long Life
Continuous Duty Capability
Low Amp Draw for Maximum Switch Life
* Typical Installation